Fiat Panda 2 1.1 New dashboard problem

[QbM78]

Hello, I have a 2006 Fiat Panda 2 with a 1.1 engine and I wanted to install the emotion version of the instrument cluster because it originally had a cluster without RPM gauge. I installed the cluster, but the display is flashing, so I wanted to perform proxy alignment, but the "Dashboard Node (IPC/NQS)" says "FAILED! - Unknown error". Someone suggested that I should change the proxy configuration manually, but I don't know which byte to change. I think this might work because when I compared the "CAN CONFIGURATION DATA" with the original cluster installed and the one with the emotion cluster, byte 40 is different, so I think there's something wrong. I'm attaching a log from MultiEcuScan showing the configuration with the original cluster and the one with the emotion cluster. Please help, I would be very grateful.

Original cluster:

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
00 00 00 0F 00 00 00 0F 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 0F 00 00 00 09 00 00 00 0F 00 00 00 09 00 00 00 09
33 32 31 36 39 30 30 30 36 33 37 4F 55 54 50 55 54 4A 49 54 20 20 05 03 22 0F 00 00 00 09 00 00 00 01 00 00 00 00 01 14 00 00 00 04 06 01 00 00 00 00 00 00 11 00 04
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
(Multiecuscan 4.6R1)
2026-02-01 14:37:18
Fiat Panda '03 1.1 8V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Ok

WARNING: This vehicle is properly configured. PROXI Alignment is not needed!

New cluster:

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
00 00 00 0F 00 00 00 0F 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 0F 00 00 00 09 00 00 00 0F 00 00 00 09 00 00 00 01
33 32 31 36 39 30 30 30 36 33 37 4F 55 54 50 55 54 4A 49 54 20 20 05 03 22 0F 00 00 00 09 00 00 00 01 00 00 00 00 01 14 00 00 00 04 06 01 00 00 00 00 00 00 11 00 04
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
(Multiecuscan 4.6R1)
2026-02-01 09:43:08
Fiat Panda '03 1.1 8V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Failed

EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) SUCCESS!
Writing to module: Dashboard Node (IPC/NQS) FAILED! - Unknown error
FAILED TO EXECUTE
Dashboard Node (IPC/NQS) FAILED! - Unknown error

[QbM78]

Proxy alignment was successfully performed with the new emotion counter - I used the ELM327 cable interface - previously I used the Bluetooth version

[abarthmultijet]

After a failed proxy you can press at a pdf picture at the main screen (bottom right corner). Post that result please

[QbM78]

There's no need for that, because the emotion counter is already working fine. But thanks for the reply