Uconnect 5 (Fiat 330 VP2 NAV ECE) flashing odometer

[wauzzz]

Hello, I replaced the original Uconnect 5 (Fiat 330 VP2 ECE) in my Fiat 500 L (199) with a Uconnect 5 (Fiat 330 VP2 NAV ECE).

Everything works.

Both radios are from 2013 and have software version VP2_CO_13.00.74.00.

Only the odometer is flashing.

Both radios have the same HEX data stored.

Without NAV:

33 31 33 33 30 30 31 38 31 36 36 4F 55 54 50 55 54 2D 53 49 54 20 15 04 30 4F 04 00 05 10 00 00 00 09 04 00 05 10 00 00 00 A5 C7 71 07 8F 20 37 10 31 00 00 06 00 07 00 84 06 15 01 1E C0 00 35 01 35 41 0A 0C 0D 00 80 1E 43 00 00 00 00 35 00 81 03 10 11 16 00 8F 00 05 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 00 00 00 80 12 00 10 00 00 00 40 00 01 00 0F 00 00 49 00 01 00 00 00

With NAV:

33 31 33 33 30 30 31 38 31 36 36 4F 55 54 50 55 54 2D 53 49 54 20 15 04 30 4F 04 00 05 10 00 00 00 09 04 00 05 10 00 00 00 A5 C7 71 07 8F 20 37 10 31 00 00 06 00 07 00 84 06 15 01 1E C0 00 35 01 35 41 0A 0C 0D 00 80 1E 43 00 00 00 00 35 00 81 03 10 11 16 00 8F 00 05 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 00 00 00 80 12 00 10 00 00 00 40 00 01 00 0F 00 00 49 00 01 00 00 00

Change NAV:

33 31 33 33 30 30 31 38 31 36 36 4F 55 54 50 55 54 2D 53 49 54 20 15 04 30 4F 04 00 05 10 00 00 00 09 04 00 05 10 00 00 00 A5 C7 71 07 8F 20 37 10 31 00 00 06 00 07 00 84 06 15 01 1E C0 00 35 01 35 41 0A 0C 0D 00 80 1E 43 00 00 00 00 35 00 81 03 10 11 16 00 8F 00 05 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 00 00 00 80 12 00 10 00 00 00 C7 00 01 00 0F 00 00 49 00 01 00 00 00

I changed the HEX of the navigation radio from 40 to C7 in byte 121.

I performed a proxy alignment.

The flashing odometer remains.

What did I do wrong?

Perhaps you can help?

Thank you very much.

Florian

[abarthmultijet]

Do you get an error message during proxy allignment?

[wauzzz]

Good evening, yes, unfortunately. The proxy isn't working. The radio isn't registered with the vehicle. I'll try to insert the pictures here.

[wauzzz]

Picture

[abarthmultijet]

After a failed proxy you will see a button here: (see attached file)

Can you upload what you see then?

[wauzzz]

Hi there, bedankt.

I will perform the proxy alignment again, and if there is a notification with my MES version, I will post it here.

[wauzzz]

@ abarthmultijet

I think I know what you mean, the report. I completely overlooked it. I'm adding it now. Sorry I have so little experience.

[abarthmultijet]

Change Byte 123 from 01 to 11

And let me know how it went.

[wauzzz]

Change Byte 123 from 01 to 11

And let me know how it went.

Hartelijk dank abarthmultijet!

Dat was precies de juiste weg. Groeten aan de provincie Noord-Brabant.