Page 1 of 1
ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 26 Jan 2010, 13:31
by frank37
Hello Yani,
please support for 166 ME 2.1,ME3.1 ECU, Xenon Adjustment and Automatic Gear.
thx
Frank
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 26 Jan 2010, 18:17
by klimekkk
Hello,
What you mean by xenon adjustment? Is this possible by ECU?
I adjusted manualy in my Alfa 166 - you have to use hex (6mm?) key and turn screw on top of electric motor - it's huge regulation this way!
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 03 Feb 2010, 17:10
by frank37
for Xenon is adjusted via the diagnostic plug, there was no bolt on the motor.
frank
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 03 Feb 2010, 18:56
by klimekkk
Hmmm. If You talking about bixenons it may be correct. Xenon before FL has manual regulation by this bolt:
http://img689.imageshack.us/img689/6144/xenon2xi.jpg
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 10 Feb 2010, 00:24
by frank37
Yes, but Xenon is adjusted via the diagnostic plug and the Fiat Examiner.
Frank
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 15 Feb 2010, 13:11
by devc
The ME 2.1 is the same as the ME 7.3.1 but without the two Lambda sensors in the exhaust branches (Bank1 & Bank2)
All the other sensors & Actuators are the same. Pre 03 156 2.5V6 (ME 2.1) & post 03 156 2.5V6(ME7.3.1)
The same diagnostic can be used.
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 25 Feb 2010, 12:07
by 156V6
devc wrote:The ME 2.1 is the same as the ME 7.3.1 but without the two Lambda sensors in the exhaust branches (Bank1 & Bank2)
All the other sensors & Actuators are the same. Pre 03 156 2.5V6 (ME 2.1) & post 03 156 2.5V6(ME7.3.1)
The same diagnostic can be used.
Does that effectively mean I could pick any of the cars listed that use the 7.3.1 ECU to communicate with my 2.1 ECU?
Re: ME 2.1,ME3.1,Xenon Adjustment and Automatic Gear 166
Posted: 14 Mar 2010, 21:56
by Nilsx
156V6 wrote:devc wrote:The ME 2.1 is the same as the ME 7.3.1 but without the two Lambda sensors in the exhaust branches (Bank1 & Bank2)
All the other sensors & Actuators are the same. Pre 03 156 2.5V6 (ME 2.1) & post 03 156 2.5V6(ME7.3.1)
The same diagnostic can be used.
Does that effectively mean I could pick any of the cars listed that use the 7.3.1 ECU to communicate with my 2.1 ECU?
Yes, that'll work. I used the GTA ECU, you'll only get a warning about the ISO code.
But i would also like to see specific support for the ME 2.1 ECU.
